Transistor Info
[PDF]Lab 3 BJT Biasing and Q-Point
ftp://ftp.ni.com/pub/devzone/tut/labb3.pdf
BJT Biasing and Q-Point ... BJT. Material and Equipment. NI ELVIS. Regulated
Power Supply. 2N3904 ... bias point ICQ, VCEQ using the following equations:.

[PDF]Lab 4 BJT Amplifiers
ftp://ftp.ni.com/pub/devzone/tut/labb4.pdf
NI ELVIS. 2N3904 NPN Transistor. Resistors: 96 k, 20 k, 10 k, 1k (2), 500, 47 ... two
BJT amplifier configurations will be investigated; the common-emitter, and.

2. Multisim Tutorial Using Bipolar Transistor Circuit - College ...
www.eng.auburn.edu/~niuguof/multisimdev/bjt.html
2. Multisim Tutorial Using Bipolar Transistor Circuit¶. Updated February 10, 2014.
This is a quick tutorial for teaching students of ELEC 2210 how to use Multisim ...

[PDF]EE100/EE42 MultiSim Tutorial - EECS Instructional Support
https://inst.eecs.berkeley.edu/.../EE100
The reference for this document is MultiSim 8 Simulation and Capture User's. Guide
(May 2005) from ... Fifth Example: Diodes. 11. Sixth Example: Transistors.

[PDF]RC RE =10 - University of Pennsylvania
www.seas.upenn.ed...
Oct 27, 2009 - University of Pennsylvania. Department of Electrical and Systems
Engineering. ESE319. Laboratory Experiment - Differential Amplifier. 1.

[PDF]Parametric Sweep Simulation of a BJT - SEAS
www.seas.gwu.e...
In this tutorial, we will discuss how to generate a typical I-V curve for a Bipolar Junction
Transistor (BJT) in Multisim. To do this, a DC Sweep simulation will be ...

[PDF]Experiment #5: Characterization of an NPN Bipolar Junction
www.seas.gwu.e...
ECE 2115: ENGINEERING ELECTRONICS LABORATORY. Experiment #5
Characterization of an NPN Bipolar Junction Transistor (BJT). COMPONENTS.

[PDF]2N2222 2N3904 IS (at 20 Degrees Celsius) 1.16E ... - SEAS
www.seas.upenn....
Sep 28, 2010 - 1. University of Pennsylvania. Department of Electrical and Systems
Engineering. ESE319. Laboratory Experiment 2 - BJT Linear Amplifier. 1.

Lab 3: Low Power Audio Amplifier, Introduction to Transistors
ecee.colorado.edu/~mathys/ecen1400/labs/lab03/index.html
Jan 31, 2014 - Goals of this Lab. Analyze and measure a simple transistor circuit.
Create a new component (LM386) in Multisim. Build a low power audio

How to Find the Q-point of a Transistor Circuit
www.learningaboutelectronics.com/.../How-to-find-the-q-point-of-a-tran...
What is shown above is a typical transistor circuit. In this article, we're going to show
how to find the quiescient or just simply the q-point of a Transistor Circuit

To design a common base amplifier using multisim
www.slideshare.net/.../to-design-a-common-base-amplifier-using-multisi...
Sep 4, 2013 - LinkedIn SlideShare. Upload · Login ... To design a common base
amplifier using multisim. 3,223. Share; Like ... Output is capacitively coupled from
collector. Base is at ac ... Common Emitter Amplifier : BJT. DoCircuits. 264.

NI Multisim: BJT collector characteristic
NI Multisim: BJT collector characteristic

Use a nested DC Sweep analysis to plot the collector characteristic of an
Time =3:50
NI Multisim: BJT base characteristic
NI Multisim: BJT base characteristic

Use a nested DC Sweep analysis to plot the base characteristic of an
Time =03:51
Multisim transistor bias
Multisim transistor bias

This video was made for a sophomore circuits course in electrical engineering at Bucknell University, USA. The video is designed to be used as the out-of-the-classroom component and combined with active learning exercises in class. This video covers how

Time =10:29
Transistor circuit connections using MultiSim to determine Beta (Ic/Ib)
Transistor circuit connections using MultiSim to determine Beta (Ic/Ib)

Professor Kleitz shows you how to connect a basic NPN transistor circuit in MultiSim to enable you to measure the currents to determine Beta. (Beta=current gain=Ic/Ib)
Time =11:23
NPN Cutoff and Saturation measurements using MultiSim
NPN Cutoff and Saturation measurements using MultiSim

Professor Kleitz uses MultiSim to show you how to measure the cutoff and saturation values for an NPN transistor.
Time =15:07
Building a Multisim Device from Manufacturer's Model
Building a Multisim Device from Manufacturer's Model

This tutorial covers the steps required to build a component from the manufacturer's Spice models in Multisim. An IRF1405 is built as an example and saved in the User Database
Time =08:44
How to bias an NPN transistor using the 4 resistor biasing technique
How to bias an NPN transistor using the 4 resistor biasing technique

none
Time =04:42
National Instruments Multisim Building transistor circuit (Video Only)
National Instruments Multisim Building transistor circuit (Video Only)

If you put it in HD you can see everything i did..build/test/even with the bode plotter
Time =13:38